Makes Your Mustang's Interior Look & Feel Like New Again!
2003-04 Cobra look for your Fox
Made in the USA
What's in the Box
(2) Headrest Upholstery
(1) Driver Seat Back Upholstery
(1) Driver Seat Bottom Upholstery
(1) Passenger Seat Back Upholstery
(1) Passenger Seat Bottom Upholstery
(2) Rear Seat Back Upholstery
(1) Rear Seat Bottom Upholstery
(1) Driver Seat Back Foam
(1) Driver Seat Bottom Foam
(1) Passenger Seat Back Foam
(1) Passenger Seat Bottom Foam
1984-1986 Mustang 2003-04 Cobra Style Sport Seat Uphoslstery
This Mustang Seat Upholstery is intended for the 1984-1986 Mustang Hatchbacks with sport high back front bucket seats. This 2003-04 Cobra Style upholstery features vinyl back & sides with Suede seating surface. Some front seats use a small headrest cover, which is included. GT's with a halo must be reused.
High Quality Vinyl Sport Seat Upholstery for Your Mustang
If the seats in your Mustang have seen better days, a set of new seat upholstery for your Fox body Mustang is just the ticket! Just follow the instructions on our Mustang seat upholstery installation blog by removing the factory seat upholstery/foam and re-cover your Mustang seats with this reproduction kit to make the seats in your Mustang look and feel like new again.
Made From OE Patterns
This 2003-04 Cobra style sport vinyl upholstery kit features OE style patterns to match the seats that your Mustang came with from the factory. It adds a great custom touch to any Fox Mustang.
- Does both front and back seats! Seat Foam replaces Front Seats Only. Rear Seat Foam is Reused.
TMI is the only interior manufacturer that offers a Limited Lifetime Warranty. This will cover any workmanship errors caused by the manufacturer and does not cover installation errors or normal wear and tear.
This seat upholstery is patterned after the original style upholstery in your vehicle. The material itself does not match the OEM material, but it is the closest available match. Upholstery age, sun fading, and other variables may cause color differences. Color samples are available upon request.
Seat upholstery is highly recommended to be installed by a trained professional. If you are installing the upholstery yourself, you will need a hog ring and plier kit.
Great upholstery and foam - only a few minor issues
chris c. on
Installed this on my 85/86 seat frames this week. Took the better part of three days to get everything, mostly because I was taking my time.
Good - really nice color and 'strong' feeling upholstery, didn't have any concerns tugging on it to get it to install. - video on YouTube was extremely helpful, especially the tip about using the bags.
Challenges - the knee bolsters assume you are using 87+ seats (even though this part # says 84-86) so the metal piece from the old seats doesn't fit the new foam and plastic mounting bracket. The 85/86 seats have a screw through a pull handle that attaches to the bracket. The new plastic piece assumes the original metal would bolt into it. Had to remove the speed nuts and drill out the plastic big enough to fit the handle and screws from the front - knee bolster bottom needs to be stapled to the plastic, but using industrial staples they push through the upholstery. Had to push the protruding staple down with pliers. - foam on the front seat, upper part needs to be compressed against the frame for any chance of getting the cover on. Once the rods are attached to the foam loops at the top, the whole thing wants to lift off the frame as you tug on it. Ended up zip-tying the rods to the frame (then cut them off when I finally got the J clips to catch.) - I also bought the carpet set from LMR and applied the new carpet when building the rear seats. Despite the video, there was no way to get the push pins to catch on the frame without first stapling the carpet to the frame (I put the latch back in to get it to line up correctly.) I then had to 'notch' the carpet around the push pin holes to get them to push in. Otherwise the carpet was too thick for the push pins to grab. The corners also needed to be trimmed to fit.
Overall, very impressed with the kit and installation, other than the few items I had to engineer around above.
TMI PRODUCTS, INC., a family-owned company, was founded in 1982 when the Tuccinardi brothers began making Volkswagen door panels in their family garage in Torrance, California. Today, TMI makes high-value interior automotive components like seating, interior consoles, floor coverings, door panels, convertible roof assemblies, headliners and integrated electronic systems for your Mustang or Lightning. TMI has mastered fast-to-market niche programs. From prototype to production, TMI's streamlined processes integrate emerging technologies for volume or short run projects. TMI's quick response to emerging market opportunities provides the industry with innovative high demand products. And TMI's attentive product refreshment plans for mid-cycle changes enable TMI's partners to offer hot, profitable products.
Shop TMI products to get your leather, vinyl, suede, and cloth Mustang upholstery at LatemodelRestoration.com!
Well i picked this car up for only $500 bucks. Yep that's right $500. It has the DIS 2.3 with and automatic. It was really beat up cosmetically when I got her. The plan is to make it a v8 manual car s...