Newest 'ford racing' Posts

How To Install Mustang Gears

Installing gears on a Mustang If you're like a lot of other people out there, you've probably wondered at some point in time whether or not you're capable of installing rear gears in your Mustang. Well, there's no clear-cut answer to that. You will need above-average mechanical capabilities along with some specialized... more

Posted by Tyler Rodriquez on 6/23/2017

How To Install Ford Racing Mustang Short Throw Shifter (2015-2017)

Tools Required: Socket Set Hammer Punch Jack/Jack Stands Or Lift Small Piece Of 2x4 Step 1: Start by removing the shift knob. Rotate the shift knob counterclockwise to remove it from the handle. Step 2: Using a plastic trim removal tool, separate the shifter bezel from the center console. ... more

Read more: 2015 mustang , mustang , shifter , ford racing , ford performance

Posted by Tyler Rodriquez on 1/5/2017

How To Install Mustang Ford Racing Aluminum Driveshaft 28 Spline (79-04)

Tools Required: 12 point socket, or box end wrench Large screwdriver, and small prybar Jack & jack stands Plastic bag Drain pan Towels Lock Tite is optional Installation Instructions Start by lifting the rear end of the car up, and supporting it with jack stands Locate, and remove the 4 bolts holding ... more

Read more: 79 93 mustang , 94 04 mustang , mustang , ford racing , driveshaft

Posted by Tyler Rodriquez on 12/15/2016

How To Install Mustang Ford Racing Aluminum Driveshaft 31 Spline (79-04)

Tools Required: 12 point socket, or box end wrench Large screwdriver, and small prybar Jack & jack stands Plastic bag Drain pan Towels Lock Tite is optional Installation Instructions Start by lifting the rear end of the car up, and supporting it with jack stands Locate, and remove the 4 bolts holding ... more

Read more: 79 93 mustang , 94 04 mustang , mustang , driveshaft , ford racing

Posted by Tyler Rodriquez on 12/7/2016

How To Install Mustang Ford Racing GT500 15" Front Brake Kit (05-14)

Installation Instructions Front Brakes Step 1: Start the installation by jacking the car up, and support it with jack stands Step 2: Remove your wheel, and loosen the brake hardline from the softline Step 3: Cap off the vehicle side of the brake line Step 4: Remove the two 10mm ... more

Read more: 05 09 mustang , 10 14 mustang , mustang , ford racing , brakes

Posted by Dustin Leathers on 12/2/2016

2011-17 Mustang Ford Performance Oil Separator

Ford Performance Oil-Air Separator This oil separator from Ford Performance is without question a high quality option when it comes to oil separators for the Coyote powered Mustangs. The heart of the kit is the canister which is made from precision molded plastic with a unique filter media that separates the o... more

Posted on 3/14/2016

How To: Install Ford Performance Rear Seat Delete & X-Brace (2005-2014)

Ford Performance Rear Seat Delete & X-Brace This rear seat delete was standard equipment on the 2012 and 2013 Boss 302 Laguna Seca racecar. It obviously deletes the rear seat, helps improve chassis rigidity and you even shave a couple of pounds. Which, when it does come to racing every last pound saved helps out tre... more

Posted by Landan Durham on 8/18/2015

How To: Build a 302/351 Mustang Engine

SVE Longblock Build Building an engine is often thought to be, an “Act of Congress” to any of us that have never really put our minds together to build one. Fortunately for all of you, we decided to throw one of our 5.0Resto Economy Short Blocks on an engine stand and get to work. Several of us shot ideas back and f... more

Posted by Landan Durham on 7/7/2015

How To: Install Ford Racing Hot Rod Cams and Intake Manifold

Ford Racing Hot Rod Cams & Intake Manifold The Ford Racing Hot Rod Cams were designed with a few things in mind, to increase horsepower and torque across the entire power band and add some serious bumpity bump to your three valve Mustang! These camshafts are engineered for naturally aspirated and supercharged applic... more

Posted by Landan Durham on 5/26/2015

How To: Install 2015-17 Mustang Ford Racing Deck Lid Trim Panel

Ford Racing Deck Lid Trim Panel The Ford Racing Deck Lid Trim Panel is the perfect "blank canvas" to add a touch of customization to your 2015-16 Mustang. This is the EXACT production trim panel that is pulled from the production process before the mounting holes are drilled for the Horse, GT, or 50th Anniversary ba... more

Read more: mustang , 2015 mustang , s550 mustang , s550 , exterior , deck lid trim panel , ford racing

Posted by Landan Durham on 5/6/2015

How To: Install Mustang GT Ford Racing PI Intake Manifold

Ford Racing Performance Improved Intake Manifold If you own a 99-01 2 valve Mustang, then your car was plagued with a factory intake manifold that featured a plastic coolant crossover. This factory crossover was prone to cracking at the front molded seam, as well as the temperature sensor and rear heater hose connec... more

Read more: mustang , 94 04 mustang , sn95 , sn95 mustang , new edge mustang , engine , intake , ford racing

Posted by Landan Durham on 5/4/2015

2015-17 Mustang Ford Racing Sport CatBack Exhaust Sound - (5.0L GT)

This Ford Racing Sport Catback features kit features their famous Sport mufflers combined with a new x-pipe that is made of 2.5" stainless steel mandrel bent tubing. Each Muffler is finished off with a 4" chrome or black tip and is made by Borla for Ford Racing right here in the USA. This kit bolts up after your cataly... more

Read more: 2015 mustang , s550 mustang , exhaust , ford racing

Posted by Landan Durham on 3/25/2015

2015-17 Mustang Ford Racing Roush Performance Supercharger Installation Guide

How-To Install the Ford Racing/Roush Performance Supercharger Read along as we walk you step-by-step through the installation process for the Ford Racing/Roush Performance Phase 1 Supercharger Kit! Required Tools: 1/4", 3/8", and 1/2" drive socket set Cordless Impact Drill Pliers Dremel Tool or other cutti... more

Read more: mustang , 2015 mustang , s550 mustang , supercharger , ford racing , roush , installation

Posted by Landan Durham on 2/23/2015

Guard Supercharged 2015 Mustang GT

Off The Lot When we first picked up this 2015 Mustang GT the Guard color really took us by surprise. We have been waiting for something similar to the Highland Green used on the 2001 Bullitt to make it's return, and the Guard color was a pretty close match. We gave this S550 a nice little makeover in the wheel, suspen... more

Read more: 2015 mustang , mustang , supercharger , ford racing , roush , velgen , eibach , lowering springs

Posted by Tyler Rodriquez on 2/10/2015

2015-17 Mustang GT Ford Racing X-Pipe Install

Are you ready to shed weight, add power and make your 2015-17 S550 sound amazing? Ford Racing has you covered with their new resonator delete x-pipe assembly for your 2015-17 S550! Installation is straight forward, but you will require some special tools and a little bit of your time. Here is the how-to for the install... more

Read more: mustang , s550 mustang , exhaust , installation , ford racing

Posted by Jay Walling on 2/6/2015

Ford Racing Cobra Jet Intake Manifold Installation

The Coyote is back! When Ford first released the Coyote engine in 2011, it sparked a wildfire in the hearts of Mustang owners everywhere. It was like 1985 all over again when Mustangs dominated the streets. Everyone wanted the legendary 5.0L under their hood. They say history always repeats itself and that ... more

Read more: mustang , 10 14 mustang , s197 mustang , installation , ford racing , intake , air fuel

Posted by Aaron Westerman on 11/25/2014

Ford Racing 2015 Mustang Supercharger Kits

2015 Mustang Superchargers - Shop Now! Click on the following link to start shopping our complete line of S550 Mustang superchargers! 2015 Mustang Superchargers SEMA 2014 UPDATE! SEMA is the place to be when it comes to seeing all the latest and greatest performance products. Ford Racing introduced a whole ... more

Read more: mustang , 2015 mustang , news , ford racing , engine , supercharger , s550 mustang

Posted by Jeff Jimenez on 11/6/2014

SVE Pace Car Gets A New Look

Once the new Aluminator XS Engine was installed in the SVE Pace Car, we immediately turned our focus toward a new look. The old look had served its purpose but had become “played out” to a certain degree. We went back and forth with ideas for what felt like days. Finally we settled on the 1979 Pace Car tribute look. Wh... more

Read more: mustang , 10 14 mustang , s197 mustang , video , ford racing , project car , sve pace car

Posted by Jeff Jimenez on 8/22/2014

Ford Racing Aluminator XS Engine Dyno

To give our SVE Pace Car a great foundation for future modifications, we turned to Ford Racing to supply us with the ultimate 5.0L Coyote Motor - better known as the Aluminator XS Crate Engine. This 5.0L 4V motor is essentially a Boss 302 crate engine on steroids. It features just about every Ford Racing engine compone... more

Read more: mustang , 10 14 mustang , s197 mustang , dyno , ford racing , engine , project car , sve pace car

Posted by Jeff Jimenez on 8/18/2014

Ford Racing Aluminator XS Engine Install

The number 8 piston on our 2011 Mustang GT finally threw in the towel and called it quits. That opened the door for the perfect opportunity to finally revamp our Project 777 car. You can follow along with the whole overhaul here – SVE Pace Car. The first step in this restoration project was to get a new engine. We ... more

Read more: 10 14 mustang , mustang , s197 mustang , ford racing , engine , project car , sve pace car

Posted by Jeff Jimenez on 8/15/2014

Ford Racing 14” Brembo Brake Kit Install (M-2300-S)

With our 2014 Mustang GT project getting serious handling and performance parts thrown at it, we had to do something about those stock non-Brembo brakes! We turned to Ford Racing and installed one of their M-2300-S 14” Brembo brake kits on our project car. We also figured we would take the time to walk you through the ... more

Read more: mustang , 05 09 mustang , 10 14 mustang , s197 , installation , video , ford racing , brakes , project car

Posted by Jeff Jimenez on 3/31/2014

Ford Racing Mustang Handling Pack Install (05-14)

Our 2014 Mustang GT project had to be about more than a great looking exterior! We wanted to handle just as well as it looked! With the Roush RS3 conversion complete, we turned out focus toward the suspension. While the S197 Mustangs perform well from the factory, we knew there was a ton of room for improvement. We wan... more

Read more: mustang , 05 09 mustang , 10 14 mustang , video , installation , project car , roush , ford racing , suspension

Posted by Jeff Jimenez on 3/27/2014

2014 Roush Mustang Build

As we gear up for the 2015 Mustang’s release, we figured what better way to say goodbye to the S197 platform than building a one last project car! If you have followed any of our previous project cars you have noticed that they have all been standard transmissions. This time around we are starting with a 2014 Ford Must... more

Read more: mustang , 10 14 mustang , project car , 2014 mustang gt , video , roush , ford racing

Posted by Jeff Jimenez on 3/7/2014

Mustang Axle Back Exhaust Comparison (11-14 5.0L)

All Mustang Enthusiasts have asked the same question at some point – what exhaust should I put on my Stang? Well thankfully, that’s a question that we can help you answer. Sure you can turn to YouTube but let’s face it you usually get some cruddy cell phone camera or decent picture with tons of wind noise. As part of o... more

Read more: mustang , 10 14 mustang , tech , video , exhaust , axle back , bassani , ford racing , flowmaster

Posted by Jeff Jimenez on 1/7/2014

Mustang 351W Engine Swap Guide

With all the buzz surrounding Fox Body Coyote engine swaps, it’s no surprise that people have turned to the capable new 5.0 as a source for making big horsepower in the beloved Fox Body platform. With the abundance of power available in its stock form, and a strong aftermarket support, the new-school 5.0 certainly... more

Read more: mustang , 79 93 mustang , 94 04 mustang , fox body , sn95 , tech , ford racing , trickflow , msd , bbk , engine

Posted by Jeff Jimenez on 1/7/2014