Newest 'mustang' Posts


Posts Tagged: mustang
Results 26 - 50 of 643
  • How to Install Mustang LX Grille Bar Eliminator

    Tools Required: -Plastic Cutting Saw -¼” Drill Bit -Masking Tape -Drill Motor -Eye Protection Installation Procedure: 1. Near the grille area, Apply a layer of masking tape to bumper cover to protect surrounding paint. 2. Remove the factory grille bar by cutting with a body saw or other equivalent cuttin... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/22/2016

  • Mustang Inner Door Belt Weatherstrip Installation (1987-1993)

    Installation Instructions Step 1: the door panel by using a flat head screwdriver, or a pair of needle nose pliers Step 2: Remove the old weatherstrip from the door panel Step 3: Line up the tab on the new weatherstrip, with the notch on the door panel Step 4: Using a power drill w... more

    Read more: 79 93 mustang , mustang , weatherstriping

    Posted by Tyler Rodriquez on 12/22/2016

  • How To Install Aluminum Mustang Radiator (05-09)

    Adding a lightwieght aluminum radiator to your 2005-2009 Mustang is a great way to drop weight from your S197 and improve your cooling system efficiency. Installing an aluminum radiator in a 2005-2009 Mustang is a pretty easy step by step process. Follow along as customer Jeremy Howell walks you through his install! ... more

    Read more: 05 09 mustang , mustang , sve

    Posted by Tyler Rodriquez on 12/21/2016

  • How To Install Fox Body Mustang Hurst Shifter (87-93)

    Let's face it, the factory shifter in your Fox Body is good, but there is plenty of room for improvement. That's where the Hurst shifter comes into play. Follow along as we walk you through this quick and easy installation. The dash pads in the 1979-86 Fox Body Mustangs have a tendency to fade and crack over the past ... more

    Read more: 79 93 mustang , mustang , shifter

    Posted by Tyler Rodriquez on 12/21/2016

  • How To Install Fox Body Mustang Headlight Switch And Harness

    Tools Required Small flat head screwdriver Wire cutters Wire strippers Pliers Heat gun Installation Instructions Step 1: Start the installation by popping the hood, and removing your negative battery cable Step 2: Remove the headlight switch from the dash, by releasing the 4 small tabs with the ... more

    Read more: mustang , 79 93 mustang

    Posted by Tyler Rodriquez on 12/20/2016

  • How To Change Mustang Gear Oil

    Tools Required: Socket Set Flat Head Screwdriver Drain Pan Gasket Scraper Brake Clean (Optional) Step 1: Lift your Mustang with either jacks and a jackstand or with a lift. Step 2: Place a bucket or drain pan under your rear end, and loosen and remove all but the top cover bolts. Ste... more

    Read more: 79 93 mustang , 94 04 mustang , 05 09 mustang , 10 14 mustang , 2015 mustang , mustang , maintenance , lmr basics

    Posted by Tyler Rodriquez on 12/20/2016

  • How To Install 1979-1986 Mustang Dash Pad

    The dash pads in the 1979-86 Fox Body Mustangs have a tendency to fade and crack over the past 20 years. Late Model Restoration offers direct replacement dash pads and has provided a quick and easy installation guide to help you get your Fox looking brand new! Tools Needed: Common Hand Tools Installation... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/20/2016

  • What Is The 302 Firing Order?

    The firing order for a Ford 302 motor is essential knowledge when building, rebuilding, or maintaining your Fox Body or SN-95 Mustang. These easy to use chart make it simple to quickly remind yourself of the 302 firing order. Screenshot or save the following graphics to keep with you at all times! more

    Read more: 79 93 mustang , 302 , 94 04 mustang

    Posted by Tyler Rodriquez on 12/15/2016

  • How to Install 1979-2004 Ford Mustang Upper & Lower Rear Control Arms

    Ford Mustang Upper & Lower Rear Control Arm Installation Instructions Step 1: Start by lifting your car up on a lift, or jack stands Step 2: Remove your rear wheels Step 3: Start by removing the sway bar hardware, if equipped by removing the 2 bolts on each rear control arm Step 4: Remove the sway bar f... more

    Read more: 79 93 mustang , 94 04 mustang , sve , control arms

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Stifflers Tubular Transmission Crossmember

    Tools Required: Basic hand tools Floor jack Jackstands Installation Instructions Raise the vehicle up to allow access for installation, and support it with jack stands Support transmission with the floor jack. Do not place the jack on the transmission pan, or block access to crossmember mounts Remove the... more

    Read more: 79 93 mustang , mustang , stifflers

    Posted by Dustin Leathers on 12/15/2016

  • How To Install Mustang Ford Racing Aluminum Driveshaft 28 Spline (79-04)

    Tools Required: 12 point socket, or box end wrench Large screwdriver, and small prybar Jack & jack stands Plastic bag Drain pan Towels Lock Tite is optional Installation Instructions Start by lifting the rear end of the car up, and supporting it with jack stands Locate, and remove the 4 bolts holding ... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , ford racing , driveshaft

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Boss 302 Rear Diffuser (13-14)

    Tools Required: Air Powered Body Saw Phillips Head 11mm Socket Flat Head Screw Driver Installation Instructions Open the trunk, and remove the 2 plastic nuts, and the 2 pushpin type retainers Release the trunk trim panel, and disconnect the trunk light electrical connector, and then remove the ... more

    Read more: 10 14 mustang , mustang , boss 302 , diffuser

    Posted by Phillip Perez on 12/15/2016

  • How to Install Mustang Fog Lights (99-04)

    Tools Needed Socket Wrench Extensions 7mm Socket Phillips head screwdriver Silicone Torx bit T20 Pliers Installation Step 1Unscrew the adjuster screw on the new fog lights. Silicone around the lenses. Let them sit for 6-8 hours or until dry. Step 2Use drive on ramps or a jack and jack stands to acce... more

    Read more: 94 04 mustang , mustang , fog lights

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Headlights (05-09)

    Tools Required: Common hand tools 05-09 Mustang Bumper Removal and Headlight Installation Instructiosn Step 1: Open your Mustang’s hood and have all tools ready. Step 2: Use the flat-blade screwdriver to remove the 6 plastic push pins that hold down the radiator cover to the car. Step 3: R... more

    Read more: 05 09 mustang , mustang , headlights

    Posted by Dustin Leathers on 12/15/2016

  • How To Install Mustang Sequential Tail Light Kit (05-09)

    Tools Required: Common hand tools Installation Instructions Step 1: Start the installation by removing the top 2 retainers in the rear trunk liner, and remove the lower 2 Step 2: Remove the 2 screw retainers with a T-27 Torx bit Step 3: Remove the rear trunk liner Step 4: W... more

    Read more: 05 09 mustang , mustang , tail lights

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Short Shifter (11-14)

    Adding a short shifter to your 2011-2014 Mustang is a great way to upgrade your MT82 transmission. The stock shifter works great, but having a short throw shifter makes getting through those gears quicker and easier. Installation is quick and easy and Late Model Restoration walks you through step by step! These instruc... more

    Read more: 10 14 mustang , mustang , shifter

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Steeda Tri-Ax Race Short Throw Shifter

    Tools Required: 8mm socket 10mm socket 10” socket extension Flathead screwdriver Pry bar Silicon Step 1: Set your parking brake. Step 2: Remove your shifter knob. Step 3: Slide the boot over the handle and grab hold of the bezel and pull upwards to pull the four clips loose. Un-plug your ... more

    Read more: 2015 mustang , mustang , shifter

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang Roush Quarter Window Scoops

    Tools Required 50/50 alcohol/water solution Masking tape Rubber roller Window Scoop Installation Make sure the vehicle’s rear quarter glass is clean and dry. The glass surface should be between 61°-81°F (16°-31°C) Use 50/50 (alcohol/water) solution to clean the rear quarter glass area where the window s... more

    Read more: 2015 mustang , mustang , roush , quarter window

    Posted by Dustin Leathers on 12/15/2016

  • How To Install Mustang SVE Billet Lower Control Arms

    Installation Instructions Raise the vehicle up by supporting it on a lift, or stand so that the rear suspension is loaded. (Wheels in contact with surface) *Note* Do one side at a time Remove the stock rear control arms bolts. Next remove the rear brake cable that is routed through the arm itself Inspect the... more

    Read more: 05 09 mustang , 10 14 mustang , mustang , control arms , sve

    Posted by Dustin Leathers on 12/15/2016

  • How To Install Mustang SVE X-Pipe Resonator Delete

    Tools Required: 15mm socket Flat head screwdriver File Jack & jack stands Masking Tape Installation Instructions Step 1: To begin installation, lift the car up, and support it with jack stands Step 2: With the car in the air, support the factory resonator with a spare jack, or jack stand ... more

    Read more: mustang , 2015 mustang , sve , exhaust

    Posted by Tyler Rodriquez on 12/15/2016

  • How To Install Mustang 5.0L Replacement Engine Harness

    Installation Instructions: Disconnect the battery Installation will be easier if upper plenum is removed Remove the factory harness, taking note on how the wires are run. Disconnect the main black, and white connectors at the back of the engine Install replacement harness following factory routing. Make sure grou... more

    Read more: 79 93 mustang , mustang , engine

    Posted by Dustin Leathers on 12/14/2016

  • How To Install Mustang SVE Mongoose T5/T45 Short Throw Shifter

    Installation Instructions Step 1: Unscrew the shift knob, and remove the shift boot, and console cover plate assembly. (Push your fingers into the boot, hook your fingers under the console plate, and lift up) Step 2: Remove the factory shift handle with a 10mm wrench Step 3: Remove the four 8mm bolts holding t... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , shifter

    Posted by Tyler Rodriquez on 12/14/2016

  • How To Install 2015-2017 Mustang Hood

    Tools Required: 13mm-1/4" Drive socket Flat head screwdriver Phillips head screwdriver 9mm-1/4" drive socket T-20 Torx-bit 11mm-1/4" drive socket 1/4" drive ratchet Medium strength LockTite Removal Of Factory Hood Remove the striker bar from the hood. The factory bolts will NOT be reused on the Cerv... more

    Read more: 2015 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016

  • How To Install Fox Body Mustang Tail Lights

    Tools Required: Ratchet & 11mm socket Removal & Installation Instructions Start the removal process by removing your interior panels covering the bulb sockets, and the nuts that hold the tail lights in place Remove the light bulbs from the tail light housing by twisting them out Remove 6 (per lens) 11mm nu... more

    Read more: 79 93 mustang , mustang , tail lights

    Posted by Tyler Rodriquez on 12/14/2016

  • 1986-93 Mustang Idle Air Control Adjuster Installation Instructions

    The Idle Air Control Adjuster spacer service kit is used to correct sludge contamination concerns of the throttle bore and plate only. Verify that the idle speed concern is not being caused by the fuel system, IABP solenoid, throttle linkage, ignition system, PVC system, EGR system, cooling system, or vacuum leaks befo... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016