Newest 'mustang' Posts

How To Install Mustang Stifflers Tubular Transmission Crossmember

Tools Required: Basic hand tools Floor jack Jackstands Installation Instructions Raise the vehicle up to allow access for installation, and support it with jack stands Support transmission with the floor jack. Do not place the jack on the transmission pan, or block access to crossmember mounts Remove the... more

Read more: 79 93 mustang , mustang , stifflers

Posted by Dustin Leathers on 12/15/2016

How To Install Mustang Ford Racing Aluminum Driveshaft 28 Spline (79-04)

Tools Required: 12 point socket, or box end wrench Large screwdriver, and small prybar Jack & jack stands Plastic bag Drain pan Towels Lock Tite is optional Installation Instructions Start by lifting the rear end of the car up, and supporting it with jack stands Locate, and remove the 4 bolts holding ... more

Read more: 79 93 mustang , 94 04 mustang , mustang , ford racing , driveshaft

Posted by Tyler Rodriquez on 12/15/2016

How To Install Mustang Boss 302 Rear Diffuser (13-14)

Tools Required: Air Powered Body Saw Phillips Head 11mm Socket Flat Head Screw Driver Installation Instructions Open the trunk, and remove the 2 plastic nuts, and the 2 pushpin type retainers Release the trunk trim panel, and disconnect the trunk light electrical connector, and then remove the ... more

Read more: 10 14 mustang , mustang , boss 302 , diffuser

Posted by Phillip Perez on 12/15/2016

How to Install Mustang Fog Lights (99-04)

Tools Needed Socket Wrench Extensions 7mm Socket Phillips head screwdriver Silicone Torx bit T20 Pliers Installation Step 1Unscrew the adjuster screw on the new fog lights. Silicone around the lenses. Let them sit for 6-8 hours or until dry. Step 2Use drive on ramps or a jack and jack stands to acce... more

Read more: 94 04 mustang , mustang , fog lights

Posted by Tyler Rodriquez on 12/15/2016

3:08

How To Install Mustang Headlights (05-09)

Tools Required: Common hand tools 05-09 Mustang Bumper Removal and Headlight Installation Instructiosn Step 1: Open your Mustang’s hood and have all tools ready. Step 2: Use the flat-blade screwdriver to remove the 6 plastic push pins that hold down the radiator cover to the car. Step 3: R... more

Read more: 05 09 mustang , mustang , headlights

Posted by Dustin Leathers on 12/15/2016

3:12

How To Install Mustang Sequential Tail Light Kit (05-09)

Tools Required: Common hand tools Installation Instructions Step 1: Start the installation by removing the top 2 retainers in the rear trunk liner, and remove the lower 2 Step 2: Remove the 2 screw retainers with a T-27 Torx bit Step 3: Remove the rear trunk liner Step 4: W... more

Read more: 05 09 mustang , mustang , tail lights

Posted by Tyler Rodriquez on 12/15/2016

How To Install Mustang Short Shifter (11-14)

Adding a short shifter to your 2011-2014 Mustang is a great way to upgrade your MT82 transmission. The stock shifter works great, but having a short throw shifter makes getting through those gears quicker and easier. Installation is quick and easy and Late Model Restoration walks you through step by step! These instruc... more

Read more: 10 14 mustang , mustang , shifter

Posted by Tyler Rodriquez on 12/15/2016

12:35

How To Install Mustang Steeda Tri-Ax Race Short Throw Shifter

Tools Required: 8mm socket 10mm socket 10” socket extension Flathead screwdriver Pry bar Silicon Step 1: Set your parking brake. Step 2: Remove your shifter knob. Step 3: Slide the boot over the handle and grab hold of the bezel and pull upwards to pull the four clips loose. Un-plug your ... more

Read more: 2015 mustang , mustang , shifter

Posted by Tyler Rodriquez on 12/15/2016

How To Install Mustang Roush Quarter Window Scoops

Tools Required 50/50 alcohol/water solution Masking tape Rubber roller Window Scoop Installation Make sure the vehicle’s rear quarter glass is clean and dry. The glass surface should be between 61°-81°F (16°-31°C) Use 50/50 (alcohol/water) solution to clean the rear quarter glass area where the window s... more

Read more: 2015 mustang , mustang , roush , quarter window

Posted by Dustin Leathers on 12/15/2016

How To Install Mustang SVE Billet Lower Control Arms

Installation Instructions Raise the vehicle up by supporting it on a lift, or stand so that the rear suspension is loaded. (Wheels in contact with surface) *Note* Do one side at a time Remove the stock rear control arms bolts. Next remove the rear brake cable that is routed through the arm itself Inspect the... more

Read more: 05 09 mustang , 10 14 mustang , mustang , control arms , sve

Posted by Dustin Leathers on 12/15/2016

How To Install Mustang 5.0L Replacement Engine Harness

Installation Instructions: Disconnect the battery Installation will be easier if upper plenum is removed Remove the factory harness, taking note on how the wires are run. Disconnect the main black, and white connectors at the back of the engine Install replacement harness following factory routing. Make sure grou... more

Read more: 79 93 mustang , mustang , engine

Posted by Dustin Leathers on 12/14/2016

4:08

How To Install Mustang SVE Mongoose T5/T45 Short Throw Shifter

Installation Instructions Step 1: Unscrew the shift knob, and remove the shift boot, and console cover plate assembly. (Push your fingers into the boot, hook your fingers under the console plate, and lift up) Step 2: Remove the factory shift handle with a 10mm wrench Step 3: Remove the four 8mm bolts holding t... more

Read more: 79 93 mustang , 94 04 mustang , mustang , shifter

Posted by Tyler Rodriquez on 12/14/2016

How To Install 2015-2017 Mustang Hood

Tools Required: 13mm-1/4" Drive socket Flat head screwdriver Phillips head screwdriver 9mm-1/4" drive socket T-20 Torx-bit 11mm-1/4" drive socket 1/4" drive ratchet Medium strength LockTite Removal Of Factory Hood Remove the striker bar from the hood. The factory bolts will NOT be reused on the Cerv... more

Read more: 2015 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How To Install Fox Body Mustang Tail Lights

Tools Required: Ratchet & 11mm socket Removal & Installation Instructions Start the removal process by removing your interior panels covering the bulb sockets, and the nuts that hold the tail lights in place Remove the light bulbs from the tail light housing by twisting them out Remove 6 (per lens) 11mm nu... more

Read more: 79 93 mustang , mustang , tail lights

Posted by Tyler Rodriquez on 12/14/2016

1986-93 Mustang Idle Air Control Adjuster Installation Instructions

The Idle Air Control Adjuster spacer service kit is used to correct sludge contamination concerns of the throttle bore and plate only. Verify that the idle speed concern is not being caused by the fuel system, IABP solenoid, throttle linkage, ignition system, PVC system, EGR system, cooling system, or vacuum leaks befo... more

Read more: 79 93 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How To Install Fox Body Underdrive Pulleys

Tools Needed: Common Tool Box Tools Impact Install Time: Approximately 1 Hour 30 Mins Difficulty: 3 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Loosen the bolts on the water pump and crank pulleys Step 3: Remove the serpentine belt by shifting the adjuster to the passenger side.... more

Read more: 79 93 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How to Install 1979-98 Mustang Transmission Mount

Tools Required Ratchets Set Wrenches Jack & Jack Stands Installation Instructions Step 1Jack the car up and place it on jack stands. Be sure to leave enough room to work under the transmission. Step 2Trace the transmission mount. This is located at the rear of your transmission. Step 3Remove the two bolts... more

Read more: 79 93 mustang , 94 04 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How To Install Fox Body Mustang Long Tube Headers

Tools Needed: Common Tool Box Tools Install Time: Approximately 1hr and 30min Difficulty: 4 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Place the vehicle on sturdy jack stands or use a drive on lift to raise the vehicle. Step 3: Remove the hose clamp at the throttle body, unplug t... more

Read more: 79 93 mustang , mustang , headers

Posted by Phillip Perez on 12/14/2016

How To Install Fox Body Mustang Shorty Headers

Tools Needed: Common Tool Box Tools Install Time: Approximately 2 Hours Difficulty: 3 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Remove the entire stock air inlet system from the vehicle, this is easily done by removing the hose clamp at the throttle body, the two mass-air mounting... more

Read more: 79 93 mustang , mustang , headers

Posted by Phillip Perez on 12/14/2016

2005-10 Ford Mustang Throttle Body Installation Instructions

Tools Needed: 1/4" Ratchet 1/4" Extension 8mm socket & 10mm deep socket T-20 Torx Needle nose pliers or flat tip 5mm Allen wrench Installation Instructions Disconnect negative battery terminal. If these instructions are followed closely, this will prevent the CHECK ENGINE light from coming on after th... more

Read more: 05 09 mustang , mustang

Posted by Phillip Perez on 12/14/2016

How To Install Mustang Chin Spoiler/Splitter Combo

Installation Instructions Tools Needed Common household tools Ratchet Set Step 1Remove the factory bumper from the car. Make sure you save all the hardware, you will be reusing this. Step 2Remove your factory chin spoiler from the bumper. Save all factory mounting hardware. Step 3Install your new ... more

Read more: 10 14 mustang , mustang

Posted by Phillip Perez on 12/14/2016

5:28

How To Install A Fox Body Cat Back Exhaust System

Adding a cat back from LMR to your Mustang will not only increase HP, but will also make you stand out from the crowd. If you are in the market an aggressive sound look no further than a Fox Body cat back exhaust. Follow along in this simple step by step installation to ensure proper fitment and get your Fox back on th... more

Read more: 79 93 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How to Install a Panhard Bar on your 2005-2014

Installation Instructions Tools Needed: Jack and jack stands 18mm wrench or socket Wrenches for adjustable panhard rods: 1”, 1-1/16”, 1-1/4” Grease gun Torque wrench Step 1:Lift vehicle and support with jack stands under the rear end. Step 2:Using an 18mm wrench or socket, remove both panhard rod bol... more

Read more: 05 09 mustang , mustang

Posted by Tyler Rodriquez on 12/14/2016

How To Install Mustang Fox Body Dash Pad (87-93)

Tools Required: Common hand tools Removal & Installation Instructions Remove all contents from your Mustang's glove box, and press in on the 2 glovebox stops far enough to allow the glovebox to release downward, and out of the way Now disconnect the plug for your glovebox light If you own a '90, or a '... more

Read more: 79 93 mustang , mustang

Posted by Tyler Rodriquez on 12/13/2016

How To Install Fox Body Mustang Anti Roll Bars

Tools Needed Floor Jack or Lift Jack Stands Ratchet Set Front Bar Installation Removing the factory front anti-roll bar Step 1Lift Vehicle and remove front wheels Step 2Remove the nut and bushing from the end link assemblies at the lower control arms (both sides). Step 3Before proceeding to step 3, suppor... more

Read more: 79 93 mustang , mustang

Posted by Tyler Rodriquez on 12/13/2016