Newest 'mustang' Posts


Posts Tagged: mustang
Results 76 - 100 of 659
  • How To Install A Fox Body Cat Back Exhaust System

    Adding a cat back from LMR to your Mustang will not only increase HP, but will also make you stand out from the crowd. If you are in the market an aggressive sound look no further than a Fox Body cat back exhaust. Follow along in this simple step by step installation to ensure proper fitment and get your Fox back on th... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016

  • How to Install a Panhard Bar on your 2005-2014

    Installation Instructions Tools Needed: Jack and jack stands 18mm wrench or socket Wrenches for adjustable panhard rods: 1”, 1-1/16”, 1-1/4” Grease gun Torque wrench Step 1:Lift vehicle and support with jack stands under the rear end. Step 2:Using an 18mm wrench or socket, remove both panhard rod bol... more

    Read more: 05 09 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016

  • How To Install Mustang Fox Body Dash Pad (87-93)

    Tools Required: Common hand tools Removal & Installation Instructions Remove all contents from your Mustang's glove box, and press in on the 2 glovebox stops far enough to allow the glovebox to release downward, and out of the way Now disconnect the plug for your glovebox light If you own a '90, or a '... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Fox Body Mustang Anti Roll Bars

    Tools Needed Floor Jack or Lift Jack Stands Ratchet Set Front Bar Installation Removing the factory front anti-roll bar Step 1Lift Vehicle and remove front wheels Step 2Remove the nut and bushing from the end link assemblies at the lower control arms (both sides). Step 3Before proceeding to step 3, suppor... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Mustang Bump Steer Kit

    Vehicle will need to be taken to a performance alignment shop after the installation for proper alignment and Bump Steer Settings Installation Instructions Tools Needed: Angle Finder Floor Jack Basic Tools Drive on Lift or Drive on Ramps Installation Difficulty: 2 out of 5 Installation Time: 2 hour... more

    Read more: mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Mustang Axle Back Exhaust (11-14)

    Tools Required Common hand tools Grinder Safety glasses Installation Instructions Step 1: To remove your stock axle backs, release the hanger from the rear insulated mount, and remove the clamp from the ball, and socket flange by removing the 13mm bolt Step 2: Slide the muffler forward, and of... more

    Read more: 10 14 mustang , mustang , exhaust , axle back

    Posted by Tyler Rodriquez on 12/12/2016

  • How To Install Mustang Axle Back Exhaust (05-09)

    Tools Required 15mm Socket 13mm Socket Installation Instructions Step 1: Use a 15mm socket to loosen the nuts on the clamped connection between the mufflers, and the over-axel pipe Step 2: Use a 13mm socket to remove the bolts that secure the muffler hangers to the frame of the vehicle Step 3: Rem... more

    Read more: 05 09 mustang , mustang , axle back , exhaust

    Posted by Dustin Leathers on 12/9/2016

  • How To Change Serpentine Belt On Ford Mustang

    Tools Required: Breaker Bar Socket Set Step 1: Pop the hood and locate the belt tensioner. Step 2: Determine what size socket or drive you will need to release pressure from the tensioner. Place the socket/drive onto the tensioner and turn counter clockwise. Step 3: While keeping tension of... more

    Read more: 79 93 mustang , 94 04 mustang , 05 09 mustang , 10 14 mustang , 2015 mustang

    Posted by Tyler Rodriquez on 12/9/2016

  • How To Install A Fox Body Mid Pipe

    Tools Needed: Hacksaw or Sawsall Common House Hold Tools Welder(See Disclaimer) Installation Instructions: Step 1: Begin by disconnecting your negative cable from your battery, as you will be disconnecting some electrical components. Place the vehicle on a lift or (4) jack stands at maximum height. This ... more

    Read more: 79 93 mustang , mustang , exhaust

    Posted by Dustin Leathers on 12/9/2016

  • How To Install Mustang GT Cold Air Intake

    Tools Needed: Common household tools Ratchet Set Installation Instructions Start the installation by removing the negative terminal of the battery, and securing the cable away from the battery terminals. Start the removal process by loosening the band clamps that hold the intake tube to the mass airflow ... more

    Read more: 94 04 mustang , mustang , cold air intake

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang GT500 Rear Spoiler

    Tools Required: Heat gun Adhesive remover Plastic putty knife Flat head screwdriver Phillips head screwdriver Ratchet & 10mm socket Removal & Installation Instructions Start the removal process by removing the 13 plastic clips that hold the trunk liner to the inner trunk lid by pulling outwards on them,... more

    Read more: 10 14 mustang , mustang , spoiler

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install 1982-1997 Mustang Fuel Filler Neck Grommet

    How To Install Mustang Fuel Filler Neck Grommet (82-97) Customer Submitted Install By Harvey Davis The fuel filler neck grommet is found on the outside of your gas tank on the same side as your fuel door. It hold the filler tube in place and over the years, can deteriorate and leak fuel. This guide will walk you thro... more

    Read more: mustang , 79 93 mustang

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang Ford Accessories GT350 Track Pack Spoiler

    How To Install 2015-2017 Mustang Ford Accessories GT350 Track Pack Spoiler Tools Needed Painters Tape Microfiber Towel Plastic Pry Tool Small Flat Head Screwdriver 10mm Socket Heat Gun Adhesive Remover Installation Instructions Lay down a few pieces of painters tape, to protect the exposed p... more

    Read more: mustang , 2015 mustang , gt350 , spoiler

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang SVE Full Length Subframe Connectors

    Tools Required Standard hand tool assortment Disk grinder/Sander MIG welder 4 jack stands, or lift 3M or SEM weldable zinc primer spray paint/primer Installation Instructions (1983-93 CONVERTIBLE ONLY, ALL OTHERS SKIP TO STEP 12) Using a Sharpie, or other marking device mark the front, and rear edges of... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , sve

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install 2015 Mustang Street Scene Front Splitter

    The 2015-2016 Mustangs got a huge makeover following the S197 platform. The new front end looks pretty aggressive from the factory, but there is plenty of room for improvement. One way to get your S550 standing out from the crowd is with a 2015 Mustang Street Scene Front Splitter. These front lips are quick and easy to... more

    Read more: 2015 mustang , mustang

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Fox Body Mustang Mass Air Conversion

    Parts & Tools Required Conversion harness Cold air intake Mass air assembly Mass air compatible PCM (Manual transmission cars use a A9L or A3M processor) (Automatic transmission cars use A9P or C3W processor) Installation Instructions Step 1: Remove your negative battery cable Step 2: Remove your... more

    Read more: 79 93 mustang , mustang

    Posted by Dustin Leathers on 12/8/2016

  • How To Install Mustang Roush Pedal Kit (15-17)

    Accelerator Cover Installation Step 1Center the Roush accelerator pedal cover over the accelerator pedal and scribe the location of the four attaching holes. Step 2Using the 1/8" drill bit, drill a pilot hole in each of the four locations. Step 3Drill the attaching holes to the finished size using the 1/... more

    Read more: 2015 mustang , mustang , roush

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang EZ-Clutch Pedal Extension

    Features: Made of High Impact ABS Extends contact surface of pedal 40mm total weight with screws is 2.7oz. Installation Time: 1 Hour Tools Needed: Flat Head Screwdriver Philips Head Screwdriver Heat Gun or Hair Dryer (optional) Installation: Step 1: Remove factory rubber pad from face o... more

    Read more: 79 93 mustang , 94 04 mustang , 05 09 mustang , 10 14 mustang , 2015 mustang , mustang

    Posted by Tyler Rodriquez on 12/7/2016

  • How to Install Mustang Cold Air intake

    Tools Needed: Common household tools Ratchet Set Installation Instructions Step 1:Remove the entire stock air inlet system from the vehicle by simply unclamping at the throttle body and removing the bolt attaching the air box to the inner fenderwell area. Disconnect all hoses, wiring, etc., and then tug upw... more

    Read more: 94 04 mustang , mustang , cold air intake

    Posted by Tyler Rodriquez on 12/7/2016

  • How to Install S197 Mustang Rear Sway Bar Location Brackets

    Installation Instructions Raise the rear of the vehicle and support the axle on jackstands so that the suspension remains loaded. Remove the rear Wheels. Remove the nuts that secure the sway bar end brackets to the axle assembly and slide the sway bar forward off the mounting studs. Remove the bolt securing... more

    Read more: 10 14 mustang , mustang

    Posted by Phillip Perez on 12/7/2016

  • How To Install Mustang Anchor Room Smoke Tint Kit

    Tools Required Microfiber towel Water/dish soap mixture in spray bottle Water in spray bottle Heat gun Installation Instructions Spray the light housing with the water/soap mixture until coated liberally Remove the backing from the light tint, and spray with the water/soap mixture Apply the tint to the ... more

    Read more: 2015 mustang , mustang , anchor room

    Posted by Dustin Leathers on 12/7/2016

  • How To Install Mustang Ford Performance 24lb Fuel Injectors

    Removal & Installation Instructions Remove UPPER intake manifold, (you do not have to remove the lower manifold), and all of the vacuum lines, and sensors hooked onto it Immediately stuff rags into holes of lower intake manifold to prevent any dirt or debris from entering the manifold, and then begin scraping the o... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , fuel injectors , ford performance

    Posted by Dustin Leathers on 12/7/2016

  • How To Install SVE Halo LED Projector Headlights

    Tools Needed: 1/4" Drive Ratchet 10mm Socket Needle Nose Pliers Wire Stripper Wire Crimper 4 Blue Quick Splice Wire Connectors 4 Blue Male Quick Wire Connectors 4 Blue Female Quick Wire Connectors 2 Red Wires (8 Inch) 2 Black Wires (8 Inch) Installation Instructions: Locate, and remove the 10mm nut ... more

    Read more: 94 04 mustang , mustang , sve

    Posted by Tyler Rodriquez on 12/7/2016

  • How To Install Mustang SVE Subframe Connectors

    Tools Required: Jack & jack stands 15mm & 17mm sockets Wire wheel, or sandpaper MIG welder Installation Instructions Step 1: Raise the vehicle. We recommend a drive on lift. Jack stands or a two post lift is not recommended. Step 2: Remove the seat track hardware and position one of the seat ... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , sve

    Posted by Tyler Rodriquez on 12/7/2016

  • How To Install Mustang Ford Racing Aluminum Driveshaft 31 Spline (79-04)

    Tools Required: 12 point socket, or box end wrench Large screwdriver, and small prybar Jack & jack stands Plastic bag Drain pan Towels Lock Tite is optional Installation Instructions Start by lifting the rear end of the car up, and supporting it with jack stands Locate, and remove the 4 bolts holding ... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , driveshaft , ford racing

    Posted by Tyler Rodriquez on 12/7/2016