Recent Posts


  • How To Install Fox Body Underdrive Pulleys

    Tools Needed: Common Tool Box Tools Impact Install Time: Approximately 1 Hour 30 Mins Difficulty: 3 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Loosen the bolts on the water pump and crank pulleys Step 3: Remove the serpentine belt by shifting the adjuster to the passenger side.... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016

  • How to Install 1979-98 Mustang Transmission Mount

    Tools Required Ratchets Set Wrenches Jack & Jack Stands Installation Instructions Step 1Jack the car up and place it on jack stands. Be sure to leave enough room to work under the transmission. Step 2Trace the transmission mount. This is located at the rear of your transmission. Step 3Remove the two bolts... more

    Read more: 79 93 mustang , 94 04 mustang , mustang

    Posted by Tyler Rodriquez on 12/14/2016

  • How To Install Fox Body Mustang Long Tube Headers

    Tools Needed: Common Tool Box Tools Install Time: Approximately 1hr and 30min Difficulty: 4 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Place the vehicle on sturdy jack stands or use a drive on lift to raise the vehicle. Step 3: Remove the hose clamp at the throttle body, unplug t... more

    Read more: 79 93 mustang , mustang , headers

    Posted by Phillip Perez on 12/14/2016

  • 2005-10 Ford Mustang Throttle Body Installation Instructions

    Tools Needed: 1/4" Ratchet 1/4" Extension 8mm socket & 10mm deep socket T-20 Torx Needle nose pliers or flat tip 5mm Allen wrench Installation Instructions Disconnect negative battery terminal. If these instructions are followed closely, this will prevent the CHECK ENGINE light from coming on after th... more

    Read more: 05 09 mustang , mustang

    Posted by Phillip Perez on 12/14/2016

  • How To Install Mustang Chin Spoiler/Splitter Combo

    Installation Instructions Tools Needed Common household tools Ratchet Set Step 1Remove the factory bumper from the car. Make sure you save all the hardware, you will be reusing this. Step 2Remove your factory chin spoiler from the bumper. Save all factory mounting hardware. Step 3Install your new ... more

    Read more: 10 14 mustang , mustang

    Posted by Phillip Perez on 12/14/2016

  • How To Install Fox Body Mustang Shorty Headers

    Tools Needed: Common Tool Box Tools Install Time: Approximately 2 Hours Difficulty: 3 out of 5 Step 1: Disconnect the negative battery terminal. Step 2: Remove the entire stock air inlet system from the vehicle, this is easily done by removing the hose clamp at the throttle body, the two mass-air mounting... more

    Read more: 79 93 mustang , mustang , headers

    Posted by Phillip Perez on 12/14/2016

  • How To Install Mustang Fox Body Dash Pad (87-93)

    Tools Required: Common hand tools Removal & Installation Instructions Remove all contents from your Mustang's glove box, and press in on the 2 glovebox stops far enough to allow the glovebox to release downward, and out of the way Now disconnect the plug for your glovebox light If you own a '90, or a '... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Fox Body Mustang Anti Roll Bars

    Tools Needed Floor Jack or Lift Jack Stands Ratchet Set Front Bar Installation Removing the factory front anti-roll bar Step 1Lift Vehicle and remove front wheels Step 2Remove the nut and bushing from the end link assemblies at the lower control arms (both sides). Step 3Before proceeding to step 3, suppor... more

    Read more: 79 93 mustang , mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Mustang Bump Steer Kit

    Vehicle will need to be taken to a performance alignment shop after the installation for proper alignment and Bump Steer Settings Installation Instructions Tools Needed: Angle Finder Floor Jack Basic Tools Drive on Lift or Drive on Ramps Installation Difficulty: 2 out of 5 Installation Time: 2 hour... more

    Read more: mustang

    Posted by Tyler Rodriquez on 12/13/2016

  • How To Install Mustang Axle Back Exhaust (11-14)

    Tools Required Common hand tools Grinder Safety glasses Installation Instructions Step 1: To remove your stock axle backs, release the hanger from the rear insulated mount, and remove the clamp from the ball, and socket flange by removing the 13mm bolt Step 2: Slide the muffler forward, and of... more

    Read more: 10 14 mustang , mustang , exhaust , axle back

    Posted by Tyler Rodriquez on 12/12/2016

  • How To Install Mustang Axle Back Exhaust (05-09)

    Tools Required 15mm Socket 13mm Socket Installation Instructions Step 1: Use a 15mm socket to loosen the nuts on the clamped connection between the mufflers, and the over-axel pipe Step 2: Use a 13mm socket to remove the bolts that secure the muffler hangers to the frame of the vehicle Step 3: Rem... more

    Read more: 05 09 mustang , mustang , axle back , exhaust

    Posted by Dustin Leathers on 12/9/2016

  • How To Change Serpentine Belt On Ford Mustang

    How To Change Serpentine Belt On Ford Mustang When your Mustang's serpentine belt starts to squeak and squeal, it may be time to swap out your serpentine belt. Late Model Restoration makes this installation quick and easy with this Mustang drive belt installation article. Tools Required: Breaker Bar Socket Set ... more

    Read more: 79 93 mustang , 94 04 mustang , 05 09 mustang , 10 14 mustang , 2015 mustang

    Posted by Tyler Rodriquez on 12/9/2016

  • How To Install A Fox Body Mid Pipe

    Tools Needed: Hacksaw or Sawsall Common House Hold Tools Welder(See Disclaimer) Installation Instructions: Step 1: Begin by disconnecting your negative cable from your battery, as you will be disconnecting some electrical components. Place the vehicle on a lift or (4) jack stands at maximum height. This ... more

    Read more: 79 93 mustang , mustang , exhaust

    Posted by Dustin Leathers on 12/9/2016

  • How To Install 2015 Mustang Street Scene Front Splitter

    The 2015-2016 Mustangs got a huge makeover following the S197 platform. The new front end looks pretty aggressive from the factory, but there is plenty of room for improvement. One way to get your S550 standing out from the crowd is with a 2015 Mustang Street Scene Front Splitter. These front lips are quick and easy to... more

    Read more: 2015 mustang , mustang

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang GT Cold Air Intake

    Tools Needed: Common household tools Ratchet Set Installation Instructions Start the installation by removing the negative terminal of the battery, and securing the cable away from the battery terminals. Start the removal process by loosening the band clamps that hold the intake tube to the mass airflow ... more

    Read more: 94 04 mustang , mustang , cold air intake

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang GT500 Rear Spoiler

    Tools Required: Heat gun Adhesive remover Plastic putty knife Flat head screwdriver Phillips head screwdriver Ratchet & 10mm socket Removal & Installation Instructions Start the removal process by removing the 13 plastic clips that hold the trunk liner to the inner trunk lid by pulling outwards on them,... more

    Read more: 10 14 mustang , mustang , spoiler

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install 1982-1997 Mustang Fuel Filler Neck Grommet

    How To Install Mustang Fuel Filler Neck Grommet (82-97) Customer Submitted Install By Harvey Davis The fuel filler neck grommet is found on the outside of your gas tank on the same side as your fuel door. It hold the filler tube in place and over the years, can deteriorate and leak fuel. This guide will walk you thro... more

    Read more: mustang , 79 93 mustang

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang Ford Accessories GT350 Track Pack Spoiler

    How To Install 2015-2017 Mustang Ford Accessories GT350 Track Pack Spoiler Tools Needed Painters Tape Microfiber Towel Plastic Pry Tool Small Flat Head Screwdriver 10mm Socket Heat Gun Adhesive Remover Installation Instructions Lay down a few pieces of painters tape, to protect the exposed painted surfa... more

    Read more: mustang , 2015 mustang , gt350 , spoiler

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Mustang SVE Full Length Subframe Connectors

    Tools Required Standard hand tool assortment Disk grinder/Sander MIG welder 4 jack stands, or lift 3M or SEM weldable zinc primer spray paint/primer Installation Instructions (1983-93 CONVERTIBLE ONLY, ALL OTHERS SKIP TO STEP 12) Using a Sharpie, or other marking device mark the front, and rear edges of... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , sve

    Posted by Tyler Rodriquez on 12/8/2016

  • How To Install Fox Body Mustang Mass Air Conversion (86-88)

    How To Install Fox Body Mustang Mass Air Conversion Parts & Tools Required Conversion harness Cold air intake Mass air assembly Mass air compatible PCM (Manual transmission cars use a A9L or A3M processor) (Automatic transmission cars use A9P or C3W processor) Installation Instructions Remove your negative... more

    Read more: 79 93 mustang , mustang

    Posted by Dustin Leathers on 12/8/2016

  • How To Install Mustang Roush Pedal Kit (15-17)

    Accelerator Cover Installation Step 1Center the Roush accelerator pedal cover over the accelerator pedal and scribe the location of the four attaching holes. Step 2Using the 1/8" drill bit, drill a pilot hole in each of the four locations. Step 3Drill the attaching holes to the finished size using the 1/... more

    Read more: 2015 mustang , mustang , roush

    Posted by Tyler Rodriquez on 12/8/2016

  • How to Install S197 Mustang Rear Sway Bar Location Brackets

    Installation Instructions Raise the rear of the vehicle and support the axle on jackstands so that the suspension remains loaded. Remove the rear Wheels. Remove the nuts that secure the sway bar end brackets to the axle assembly and slide the sway bar forward off the mounting studs. Remove the bolt securing... more

    Read more: 10 14 mustang , mustang

    Posted by Phillip Perez on 12/7/2016

  • How To Install Mustang Ford Performance 24lb Fuel Injectors

    Removal & Installation Instructions Remove UPPER intake manifold, (you do not have to remove the lower manifold), and all of the vacuum lines, and sensors hooked onto it Immediately stuff rags into holes of lower intake manifold to prevent any dirt or debris from entering the manifold, and then begin scraping the o... more

    Read more: 79 93 mustang , 94 04 mustang , mustang , fuel injectors , ford performance

    Posted by Dustin Leathers on 12/7/2016

  • How To Install Mustang EZ-Clutch Pedal Extension

    Features: Made of High Impact ABS Extends contact surface of pedal 40mm total weight with screws is 2.7oz. Installation Time: 1 Hour Tools Needed: Flat Head Screwdriver Philips Head Screwdriver Heat Gun or Hair Dryer (optional) Installation: Step 1: Remove factory rubber pad from face o... more

    Read more: 79 93 mustang , 94 04 mustang , 05 09 mustang , 10 14 mustang , 2015 mustang , mustang

    Posted by Tyler Rodriquez on 12/7/2016

  • How To Install Mustang Cold Air intake

    How To Install Mustang Cold Air Intake (96-04) If you are looking to add more power and increase air flow in your 96-04 Mustang, look no further than a cold air intake. Follow along as we show you step by step how to install a cold air intake on your 4.6L Stang! Tools Needed: Common household tools Ratchet Set ... more

    Read more: 94 04 mustang , mustang , cold air intake

    Posted by Tyler Rodriquez on 12/7/2016