Powered by Mustang Enthusiasts - Call Now (866) 507-3786

3M Adhesion Promoter for Double Sided Tape - 2pc


Details   |  Videos   |  Reviews

Details   |   Videos   |   Reviews
3M Adhesion Promoter for Double Sided Tape - 2pc
3M Adhesion Promoter for Double Sided Tape - 2pc
How To Install Fox Body Mustang Door Body Side Moldings (79-93)

Make sure your new body components stick to your car with some extra help from this 3M Adhesion Promoter!



Item #3M-06396K
MPN# 3M-06396K

Everyday Low Price: $10.99

In Stock Ships tomorrow!
 This item is returnable. Details

Free Shipping over $99

 Add to Cart

× close

 Benefits

  • Keeps double sided tape stuck!
  • Easy application

 Features

  • Formulated for use with 3M Automotive Double Sided Adhesive

 What's in the Box

  • (2) Adhesion Promoter Packet

This 3M Adhesion Promoter should be part of your process is you are installing anything that uses 3M Automotive Double Sided Tape.

Surface Preparation:
The bonding surface should be clean and dry. Contaminated surfaces should be cleaned with an untreated, lint-free cloth and a mild soap & water solution. Follow this by wiping with another untreated, lint-free cloth and isopropyl alcohol.

Application Procedure:
3Mâ„¢ Adhesion Promoter 06396 is supplied in an easy-to-use sponge applicator packet. The liquid contents of the packet should be completely used as soon as possible after opening. Hold packet upright and avoid squeezing an opened packet to prevent spillage of liquid contents. The packet can be opened by tearing across the top of the packet at the notches. This will expose the sponge applicator. Do not remove the sponge or squeeze a freshly opened packet. Handling the bottom section of the packet should enable application of 3M adhesion promoter 06396 with no mess.

Apply a thin, uniform coating to the bonding surface, using the minimum amount that will fully coat the surface. A wet coating thickness of 0.002 inch or less ensures a good application. Although drying times may vary due to temperature and/or humidity, a drying time of 30-90 seconds results with a coating of this thickness. The primer should be dry before applying tape. For best results, apply tape immediately after primer application or no more than one hour after primer application. Be sure the primer surface remains free from contaminants prior to tape application.

Clean Up:
3M adhesion promoter 06396 can be cleaned up with methylethyl ketone (MEK) or acetone solvents (be careful with solvents on plastics). Vigorous scrubbing may be required. To prevent cosmetic damage to visible surfaces, be sure to apply the promoter or any solvents only to areas that will be fully covered by the part.

Caution: When using solvents for cleanup, use the precautionary measures recommended in the MSDS for the solvent.

How To Install Fox Body Mustang Door Body Side Moldings (79-93)

Check out our YouTube channel for even more tech tips, installation videos, how-tos, and more. The best place to go for anything Mustang related!


California Residents:
Prop 65 Warning SignWARNING: Cancer and Reproductive Harm- www.P65Warnings.ca.gov

Look for Similar Items by Category

Ford Mustang Parts » Mustang Body Parts | Mustang Exterior & Body » Mustang Body Moldings » Mustang Door Molding
1979-1993 Mustang Fox Body Parts » 1979-1993 Mustang Fox Body Exterior Body Parts » Fox Body Mustang Restoration Guide: Exterior » How To Remove/Install Mustang Body Moldings (87-93)
Ford Mustang Parts » Mustang Body Parts | Mustang Exterior & Body » Mustang Window Louvers and Quarter Window Parts
Ford Mustang Parts » Mustang Body Parts | Mustang Exterior & Body » Mustang Window Louvers and Quarter Window Parts
1979-1993 Mustang Fox Body Parts » 1979-1993 Mustang Fox Body Exterior Body Parts » 1979-1993 Fox Body Mustang Body Side Moldings & Kits

Products by Vehicle

Add to Cart