1999-01 Mustang SVE Aluminum Driveshaft Cobra by SVE Products ®

Reduce rotational mass and improve acceleration on your 1999-2001 Cobra with this lightweight 31-spline SVE aluminum driveshaft!

Item #LRS-4602CB

Everyday Low Price: $649.99

Out of Stock

This item is returnable. Details

× close

Images

Ford Mustang - 1999, 2000, 2001
Sub Models: Cobra

Fitment Notice

Fits 1999-2001 Cobra w/ T-45/TR3650
Will not work on Cobra independent rear suspension using Ford Performance Cobra Pinion Flange found on 03-04 cobra IRS differential.

Additional Installation Note

Clearance between the mufflers/exhaust and driveshaft needs to be verified regardless of ride height, and it needs to be checked with the suspension compressed (car at ride height).
1993-2004 Mustangs will sometimes have interference issues between the driveshaft and the front parking brake cable bracket that is spot-welded to the underside of the transmission tunnel. Sometimes, the spot welds break, and the bracket will make contact with the driveshaft. Lowered ride height will make this issue worse. The bracket can be trimmed slightly for more clearance. If the spot welds have broken, they MUST be repaired to rectify the situation.

Product Note

Measures 45.5" long, center of u-joint to center of u-joint.

Benefits

100% American Made Components
Fully-Assembled, Ready For Install
High-Quality To Withstand Everyday Driving
Reduces Rotational Weight
Improves Acceleration

Features

3.5" 6061-T6 Aluminum Tubing
31 Spline Neapco Yoke
1330 Spicer U-Joints
High-Speed Balanced
Autoweld Mig Welded

What's in the Box

(1) SVE Aluminum Driveshaft

SVE Aluminum Driveshaft
Achieve quicker acceleration, reduced weight, and less rotational mass with SVE's 1999-2001 Cobra aluminum driveshaft! Factory driveshafts are constructed from heavier steel, which adds additional lag to your engine. Swapping to an aluminum driveshaft reduces that rotational mass, which improves acceleration and also reduces potential drivetrain vibrations. These SVE aluminum driveshafts Weigh in at just a little over 14 lbs. when compared to most factory driveshafts weighing in over 18 lbs. This is a significant reduction of rotational mass. The addition of this driveshaft will result in a more efficient drivetrain which gets your Mustang moving. Pick up this aluminum 1999-2001 Cobra driveshaft from LMR to finish out your driveline upgrades!

High Performance and High-Quality
This SVE driveshaft is engineered and manufactured with precision and high-quality components. Assembled with Alcoa 6061-T6 3.5" aluminum tubing, 1330 series Spicer high-performance universal joints, and American-made flanges, this driveshaft will be sure to impress. With a .125" wall thickness, this driveshaft is rated up to 5,000 pound-ft. in torsional yield and 13,900 RPM for critical speed. Fully mig welded using an Autoweld welder on Shaftmasters machines for superior welds. High-speed balancing further reduces driveline vibration and improves overall ride quality!

SVE Products Limited Warranty - Click Here

California Residents:

WARNING: Cancer and Reproductive Harm- www.P65Warnings.ca.gov

About This Brand

Special Vehicle Equipment is a brand focused on providing superior performance and restoration parts for 1979-present Mustang and Ford Lightning trucks. From kits to swap solutions, SVE fuels the enthusiast lifestyle with problem-solving solutions that provide performance with a purpose. Comprised of the highest quality materials, all SVE products display the thorough research and meticulous attention to detail that went into the development of that part. Rest assured that when you purchase an SVE part, you will know you are purchasing a quality solution that will save you time and money.