2011-2014 Mustang GT SVE Off Road X-Pipe Install

2011-2014 Mustang GT SVE Off Road X-Pipe Install

Get it by Christmas! Order by December 16, 2016 @ 3pm CT

2011-2014 Mustang GT SVE Off Road X-Pipe Install

Posted 1/26/2015 by Tyler Rodriquez


Increase horsepower and torque while giving your S197 an aggressive new exhaust tone with this 2011-2014 Mustang SVE Off Road X Pipe!

FOLLOW: s197 , mustang , installation , exhaust , 10 14 mustang , sve

2011-2014 Mustang GT SVE Off Road X-Pipe

There is no denying that the Coyote motor puts down an impressive amount of power straight from the factory, but like everyone else, we wanted more! We also wanted to give our 2013 GT a meaner exhaust tone while picking up those extra horses. The solution, a 2011-2014 Mustang SVE off-road x pipe! This 3" mandrel bent midpipe is a direct bolt on installation and does not include catalytic converters, giving you an easy to install product that maximizes horsepower gains. Follow along as we walk you through the install. THIS X PIPE WILL REQUIRE A TUNE


Installation Instructions

  1. Disconnect The Negative Battery Cable
  2. Jack Your Car Up And Secure It On Jack Stands
  3. Spray Penetrating Oil On Your Manifold To Midpipe Bolts To Ease With Removal
  4. Starting On The Driver's Side, Loosen Both Bolts With a 15mm Deep Socket Or Ratchet Wrench
  5. Do The Same For The Lower Nut On The Passenger Side
  6. Using A Combination Of Extensions And A Swivel Socket, Loosen The Top Nut On The Passenger Side
  7. Once The Nuts Have Been Removed, Disconnect Both O2 Sensors
  8. Loosen All 4 Nuts On The Exhaust Sleeves Near The Rear Of The Midpipe With A 15mm Deep Socket
  9. Slide Back The Exhaust Sleeves And Pry Up On The Flange To Release It From The Pipes
  10. With The Help Of A Friend, Remove The Factory Midpipe
  11. Remove The Factory Gaskets And O2 Sensors with a 7/8" Open End Wrench
  12. Assemble The SVE X Pipe And Loosely Tighten The Clamps
  13. With The Included Hardware, Reinstall Onto The Factory Manifolds And Reinstall The Gaskets
  14. With The Help Of A Friend, Position The SVE X Pipe Into Place And Loosely Tighten The Nuts
  15. Tighten Down The Front Bolts And Slide The Exhaust Sleeves Onto The New X Pipe
  16. Tighten Down The Sleeves And The Included Clamps
  17. Reinstall And Reconnect The O2 Sensors
  18. Double Check That Everything Is Reconnected And Tightened
  19. Reconnect The Negative Battery Cable

Results

Our 2013 Mustang GT picked up an impressive 21 horsepower and 17 ft/lbs of torque from this SVE X Pipe. Driving this car before and after the installation, I could easily feel and hear the difference. Since this X Pipe does not include catalytic converters, the exhaust was much louder and more aggressive. Gaining over 20 horsepower for a simple bolt on was a great way to give this GT a quick and easy performance gain! (NOTE) These power numbers were made on our 2013 GT that is not stock trim. This vehicle has a VMP supercharger, 3.73 gears and VMP custom 93 octane tune. Actual power output may vary from the above mentioned horsepower gains.

2011-2014 Mustang GT SVE Off Road X-Pipe Install - 2011-2014 Mustang GT SVE Off Road X-Pipe Install

Comments